9. Directory Service

FreeNAS® supports integration with the following directory services:

It also supports Kerberos Realms, Kerberos Keytabs, and the ability to add additional parameters to Kerberos Settings.

This section summarizes each of these services and their available configurations within the FreeNAS® GUI.

9.1. Active Directory

Active Directory (AD) is a service for sharing resources in a Windows network. AD can be configured on a Windows server that is running Windows Server 2000 or higher or on a Unix-like operating system that is running Samba version 4. Since AD provides authentication and authorization services for the users in a network, you do not have to recreate these user accounts on the FreeNAS® system. Instead, configure the Active Directory service so that it can import the account information and imported users can be authorized to access the CIFS shares on the FreeNAS® system.

Note

if your network contains an NT4 domain controller, or any domain controller containing a version which is earlier than Windows 2000, configure NT4 instead.

Many changes and improvements have been made to Active Directory support within FreeNAS®. If you are not running the latest FreeNAS® 9.3-STABLE, it is strongly recommended that you update the system before attempting Active Directory integration.

Before configuring the Active Directory service, ensure name resolution is properly configured by ping ing the domain name of the Active Directory domain controller from Shell on the FreeNAS® system. If the ping fails, check the DNS server and default gateway settings in Network ‣ Global Configuration on the FreeNAS® system.

Next, add a DNS record for the FreeNAS® system on the Windows server and verify that you can ping the hostname of the FreeNAS® system from the domain controller.

Active Directory relies on Kerberos, which is a time sensitive protocol. This means that the time on both the FreeNAS® system and the Active Directory Domain Controller can not be out of sync by more than a few minutes. The best way to ensure that the same time is running on both systems is to configure both systems to:

  • use the same NTP server (set in System ‣ NTP Servers on the FreeNAS® system)
  • have the same timezone
  • be set to either localtime or universal time at the BIOS level

Figure 9.1a shows the screen that appears when you click Directory Service ‣ Active Directory. Table 9.1a describes the configurable options. Some settings are only available in Advanced Mode. To see these settings, either click the “Advanced Mode” button or configure the system to always display these settings by checking the box “Show advanced fields by default” in System ‣ Advanced.

Figure 9.1a: Configuring Active Directory

_images/ad1.png

Table 9.1a: Active Directory Configuration Options

Setting Value Description
Domain Name string name of Active Directory domain (e.g. example.com) or child domain (e.g. sales.example.com); this setting is mandatory and the GUI will refuse to save the settings if the domain controller for the specified domain can not be found
Domain Account Name string name of the Active Directory administrator account; this setting is mandatory and the GUI will refuse to save the settings if it can not connect to the domain controller using this account name
Domain Account Password string password for the Active Directory administrator account; this setting is mandatory and the GUI will refuse to save the settings if it can not connect to the domain controller using this password
NetBIOS Name string only available in “Advanced Mode”; automatically populated with the original hostname of the system; use caution when changing this setting as setting an incorrect value can corrupt an AD installation
Encryption Mode drop-down menu only available in “Advanced Mode”; choices are Off, SSL, or TLS
Certificate drop-down menu only available in “Advanced Mode”; select the certificate of the LDAP server if SSL connections are used; if you do not have a certificate, first create a CA (in CAs) then the certificate (in Certificates)
Verbose logging checkbox only available in “Advanced Mode”; if checked, logs attempts to join the domain to /var/log/messages
UNIX extensions checkbox only available in “Advanced Mode”; only check this box if the AD server has been explicitly configured to map permissions for UNIX users; checking this box provides persistent UIDs and GUIDs, otherwise, users/groups get mapped to the UID/GUID range configured in Samba
Allow Trusted Domains checkbox only available in “Advanced Mode”; should only be enabled if network has active domain/forest trusts and you need to manage files on multiple domains; use with caution as it will generate more winbindd traffic, slowing down the ability to filter through user/group information
Use Default Domain checkbox only available in “Advanced Mode”; when unchecked, the domain name is prepended to the username; if “Allow Trusted Domains” is checked and multiple domains use the same usernames, uncheck this box to prevent name collisions
Allow DNS updates checkbox when unchecked, disables Samba from doing DNS updates when joining a domain
Site Name string only available in “Advanced Mode”; the relative distinguished name of the site object in Active Directory
Domain Controller string only available in “Advanced Mode”; if the hostname of the domain controller to use is specified, make sure it is resolvable
Global Catalog Server string only available in “Advanced Mode”; if the hostname of the global catalog server to use is specified, make sure it is resolvable
Kerberos Realm drop-down menu only available in “Advanced Mode”; select the realm created using the instructions in Kerberos Realms
Kerberos keytab drop-down menu only available in “Advanced Mode”; browse to the location of the keytab created using the instructions in Kerberos Keytabs
AD timeout integer only available in “Advanced Mode”; in seconds, increase if the AD service does not start after connecting to the domain
DNS timeout integer only available in “Advanced Mode”; in seconds, increase if AD DNS queries timeout
Idmap backend drop-down menu and Edit only available in “Advanced Mode”; select the backend to use to map Windows security identifiers (SIDs) to UNIX UIDs and GIDs; see Table 9.1b for a summary of the available backends; click the “Edit” link to configure that backend’s editable options
Windbind NSS Info drop-down menu only available in “Advanced Mode” and defines the schema to use when querying AD for user/group info; rfc2307 uses the RFC2307 schema support included in Windows 2003 R2, sfu20 is for Services For Unix 3.0 or 3.5, and sfu is for Services For Unix 2.0
SASL wrapping drop-down menu only available in “Advanced Mode” and defines how LDAP traffic is transmitted; choices are plain (plain text), sign (signed only), or seal (signed and encrypted); Windows 2000 SP3 and higher can be configured to enforce signed LDAP connections
Enable checkbox uncheck to disable the configuration without deleting it

Table 9.1b summarizes the backends which are available in the “Idmap backend” drop-down menu. Each backend has its own man page which should be referred to for implementation details. Since selecting the wrong backend will break Active Directory integration, a pop-up menu will appear whenever you attempt to change this setting.

Table 9.1b: Available ID Mapping Backends

Value Description
ad AD server uses RFC2307 or Services For Unix schema extensions; mappings must be provided in advance by adding the uidNumber attributes for users and gidNumber attributes for groups in the AD
adex AD server uses RFC2307 schema extensions and supports domain trusts as well as two-way cross-forest trusts; mappings must be provided in advance by adding the POSIX attribute information to the users and groups objects in AD using a tool such as “Identity Services for Unix” on Windows 2003 R2 and later
autorid similar to “rid”, but automatically configures the range to be used for each domain, so there is no need to specify a specific range for each domain in the forest; the only needed configuration is the range of UID/GIDs to use for user/group mappings and an optional size for the ranges
hash uses a hashing algorithm for mapping and can be used to support local name mapping files
ldap stores and retrieves mapping tables in an LDAP directory service; default for “LDAP” directory service
nss provides a simple means of ensuring that the SID for a Unix user is reported as the one assigned to the corresponding domain user
rfc2307 an AD server is required to provide the mapping between the name and SID and an LDAP server is required to provide the mapping between the name and the UID/GID
rid default for “AD” and “NT4” directory services; requires an explicit idmap configuration for each domain, using disjoint ranges where a writeable default idmap range should be defined, using a backend like “tdb” or “ldap”
tdb default backend used by winbindd for storing mapping tables
tdb2 substitute for “tdb” used by winbindd in clustered environments

Click the “Rebuild Directory Service Cache” button if you add a user to Active Directory who needs immediate access to FreeNAS®; otherwise this occurs automatically once a day as a cron job.

Note

Active Directory places restrictions on which characters are allowed in Domain and NetBIOS names. If you are having problems connecting to the realm, verify that your settings do not include any disallowed characters. Also, the Administrator Password cannot contain the $ character. If a $ exists in the domain administrator’s password, kinit will report a “Password Incorrect” error and ldap_bind will report an “Invalid credentials (49)” error.

Once you have configured the Active Directory service, it may take a few minutes for the Active Directory information to be populated to the FreeNAS® system. Once populated, the AD users and groups will be available in the drop-down menus of the “Permissions” screen of a volume/dataset. For performance reasons, every available user may not show in the listing. However, it will autocomplete all applicable users if you start typing in a username.

You can verify which Active Directory users and groups have been imported to the FreeNAS® system by using these commands within the FreeNAS® Shell. To view users:

wbinfo -u

To view groups, use:

wbinfo -g

In addition, wbinfo -t will test the connection and, if successful, will give a message similar to:

checking the trust secret for domain YOURDOMAIN via RPC calls succeeded

To manually check that a specified user can authenticate:

net ads join -S dcname -U username

If no users or groups are listed in the output of those commands, these commands will provide more troubleshooting information:

getent passwd

getent group

If the wbinfo commands display the network’s users, but they do not show up in the drop-down menu of a Permissions screen, it may be because it is taking longer then the default 10 seconds for the FreeNAS® system to join Active Directory. Try bumping up the value of “AD timeout” to 60 seconds.

9.1.1. Troubleshooting Tips

If you are running AD in a 2003/2008 mixed domain, refer to for instructions on how to prevent the secure channel key from becoming corrupt.

Active Directory uses DNS to determine the location of the domain controllers and global catalog servers in the network. Use the host -t srv _ldap._tcp.domainname.com command to determine the network’s SRV records and, if necessary, change the weight and/or priority of the SRV record to reflect the fastest server. More information about SRV records can be found in the Technet article How DNS Support for Active Directory Works.

The realm that is used depends upon the priority in the SRV DNS record, meaning that DNS can override your Active Directory settings. If you are unable to connect to the correct realm, check the SRV records on the DNS server. This article describes how to configure KDC discovery over DNS and provides some examples of records with differing priorities.

If the cache becomes out of sync due to an AD server being taken off and back online, resync the cache using Directory Service ‣ Active Directory ‣ Rebuild Directory Service Cache.

An expired password for the administrator account will cause kinit to fail, so ensure that the password is still valid. Also, double-check that the password on the AD account being used does not include any spaces or special symbols, and is not unusually long.

If the Windows server version is lower than 2008 R2, try creating a “Computer” entry on the Windows server’s OU. When creating this entry, enter the FreeNAS® hostname in the “name” field. Make sure that it is under 15 characters and that it is the same name as the one set in the “Hostname” field in Network ‣ Global Configuration and the “NetBIOS Name” in Directory Service ‣ Active Directory settings. Make sure the hostname of the domain controller is set in the “Domain Controller” field of Directory Service ‣ Active Directory.

9.1.2. If the System Will not Join the Domain

If the system will not join the active directory domain, try running the following commands in the order listed. If any of the commands fail or result in a traceback, create a bug report at bugs.freenas.org that includes the commands in the order which they were run and the exact wording of the error message or traceback.

Start with these commands, where the echo commands should return a value of 0 and the klist command should show a Kerberos ticket:

sqlite3 /data/freenas-v1.db "update directoryservice_activedirectory set ad_enable=1;"
echo $?
service ix-kerberos start
service ix-nsswitch start
service ix-kinit start
service ix-kinit status
echo $?
klist

Next, only run these two commands if the “Unix extensions” box is checked in “Advanced Mode” and a keytab has been uploaded using Kerberos Keytabs:

service ix-sssd start
service sssd start

Finally, run these commands. Again, the echo command should return a 0:

python /usr/local/www/freenasUI/middleware/notifier.py start cifs
service ix-activedirectory start
service ix-activedirectory status
echo $?
python /usr/local/www/freenasUI/middleware/notifier.py restart cifs
service ix-pam start
service ix-cache start &

9.2. LDAP

FreeNAS® includes an OpenLDAP client for accessing information from an LDAP server. An LDAP server provides directory services for finding network resources such as users and their associated permissions. Examples of LDAP servers include Microsoft Server (2000 and newer), Mac OS X Server, Novell eDirectory, and OpenLDAP running on a BSD or Linux system. If an LDAP server is running on your network, you should configure the FreeNAS® LDAP service so that the network’s users can authenticate to the LDAP server and thus be provided authorized access to the data stored on the FreeNAS® system.

Note

LDAP authentication for CIFS shares will be disabled unless the LDAP directory has been configured for and populated with Samba attributes. The most popular script for performing this task is smbldap-tools and instructions for using it can be found at The Linux Samba-OpenLDAP Howto. In addition, the LDAP server must support SSL/TLS and the certificate for the LDAP server needs to be imported.

Figure 9.2a shows the LDAP Configuration screen that is seen when you click Directory Service ‣ LDAP.

Figure 9.2a: Configuring LDAP

_images/ldap1.png

Table 9.2a summarizes the available configuration options. Some settings are only available in Advanced Mode. To see these settings, either click the “Advanced Mode” button or configure the system to always display these settings by checking the box “Show advanced fields by default” in System ‣ Advanced.

If you are new to LDAP terminology, skim through the OpenLDAP Software 2.4 Administrator’s Guide.

Table 9.2a: LDAP Configuration Options

Setting Value Description
Hostname string hostname or IP address of LDAP server
Base DN string top level of the LDAP directory tree to be used when searching for resources (e.g. dc=test,dc=org)
Bind DN string name of administrative account on LDAP server (e.g. cn=Manager,dc=test,dc=org)
Bind password string password for “Root bind DN”
Allow Anonymous Binding checkbox only available in “Advanced Mode”; instructs LDAP server to not provide authentication and to allow read and write access to any client
User Suffix string only available in “Advanced Mode” and optional; can be added to name when user account added to LDAP directory (e.g. dept. or company name)
Group Suffix string only available in “Advanced Mode” and optional; can be added to name when group added to LDAP directory (e.g. dept. or company name)
Password Suffix string only available in “Advanced Mode” and optional; can be added to password when password added to LDAP directory
Machine Suffix string only available in “Advanced Mode” and optional; can be added to name when system added to LDAP directory (e.g. server, accounting)
SUDO Suffix string only available in “Advanced Mode”; use if LDAP-based users need superuser access
Kerberos Realm drop-down menu only available in “Advanced Mode”; select the realm created using the instructions in Kerberos Realms
Kerberos Keytab drop-down menu only available in “Advanced Mode”; browse to the location of the keytab created using the instructions in Kerberos Keytabs
Encryption Mode drop-down menu only available in “Advanced Mode”; choices are Off, SSL, or TLS; note that either SSL or TLS and a “Certificate” must be selected in order for authentication to work
Certificate drop-down menu only available in “Advanced Mode”; select the certificate of the LDAP server or the CA that signed that certificate (required if authentication is used); iIf your LDAP server does not already have a certificate, create a CA using CAs, then the certificate using Certificates and install the certificate on the LDAP server
LDAP timeout integer increase this value (in seconds) if obtaining a Kerberos ticket times out
DNS timeout integer increase this value (in seconds) if DNS queries timeout
Idmap backend drop-down menu and Edit only available in “Advanced Mode”; select the backend to use to map Windows security identifiers (SIDs) to UNIX UIDs and GIDs; see Table 9.1b for a summary of the available backends; click the “Edit” link to configure that backend’s editable options
Samba Schema checkbox only available in “Advanced Mode”; only check this box if you need LDAP authentication for CIFS shares and you have already configured the LDAP server with Samba attributes
Auxiliary Parameters string additional options for sssd.conf(5)
Schema drop-down menu if “Samba Schema” is checked, select the schema to use; choices are rfc2307 and rfc2307bis
Enable checkbox uncheck to disable the configuration without deleting it

Click the “Rebuild Directory Service Cache” button if you add a user to LDAP who needs immediate access to FreeNAS®; otherwise this occurs automatically once a day as a cron job.

Note

FreeNAS® automatically appends the root DN. This means that you should not include the scope and root DN when configuring the user, group, password, and machine suffixes.

After configuring the LDAP service, the LDAP users and groups should appear in the drop-down menus of the “Permissions” screen of a volume/dataset. To verify that the users have been imported, type getent passwd from Shell. To verify that the groups have been imported, type getent group.

If the users and groups are not listed, refer to the Common errors encountered when using OpenLDAP Software for common errors and how to fix them. When troubleshooting LDAP, open Shell and look for error messages in /var/log/auth.log.

9.3. NIS

Network Information Service (NIS) is a service which maintains and distributes a central directory of Unix user and group information, hostnames, email aliases and other text-based tables of information. If a NIS server is running on your network, the FreeNAS® system can be configured to import the users and groups from the NIS directory.

Figure 9.3a shows the configuration screen which opens when you click Directory Service ‣ NIS. Table 9.3a summarizes the configuration options.

Figure 9.3a: NIS Configuration

_images/nis1.png

Table 9.3a: NIS Configuration Options

Setting Value Description
NIS domain string name of NIS domain
NIS servers string comma delimited list of hostnames or IP addresses
Secure mode checkbox if checked, ypbind(8) will refuse to bind to any NIS server that is not running as root on a TCP port number over 1024
Manycast checkbox if checked, ypbind will bind to the server that responds the fastest; this is useful when no local NIS server is available on the same subnet
Enable checkbox uncheck to disable the configuration without deleting it

Click the “Rebuild Directory Service Cache” button if you add a user to NIS who needs immediate access to FreeNAS®; otherwise this occurs automatically once a day as a cron job.

9.4. NT4

This service should only be configured if the Windows network’s domain controller is running NT4. If the network’s domain controller is running a more recent version of Windows, you should configure Active Directory instead.

Figure 9.4a shows the configuration screen that appears when you click Directory Service ‣ NT4. These options are summarized in Table 9.4a. Some settings are only available in Advanced Mode. To see these settings, either click the “Advanced Mode” button or configure the system to always display these settings by checking the box “Show advanced fields by default” in System ‣ Advanced.

Figure 9.4a: NT4 Configuration Options

_images/nt1.png

Table 9.4a: NT4 Configuration Options

Setting Value Description
Domain Controller string hostname of domain controller
NetBIOS Name string hostname of FreeNAS system ; cannot be greater than 15 characters
Workgroup Name string name of Windows server’s workgroup
Administrator Name string name of the domain administrator account
Administrator Password string input and confirm the password for the domain administrator account
Use default domain checkbox only available in “Advanced Mode”; when unchecked, the domain name is prepended to the username
Idmap backend drop-down and Edit menu only available in “Advanced Mode”; select the backend to use to map Windows security identifiers (SIDs) to UNIX UIDs and GIDs; see Table 9.1b for a summary of the available backends; click the “Edit” link to configure that backend’s editable options
Enable checkbox uncheck to disable the configuration without deleting it

Click the “Rebuild Directory Service Cache” button if you add a user to Active Directory who needs immediate access to FreeNAS®; otherwise this occurs automatically once a day as a cron job.

9.5. Kerberos Realms

Beginning with FreeNAS® 9.3, a default Kerberos realm is created for the local system. Directory Service ‣ Kerberos Realms can be used to view and add Kerberos realms. If the network contains a KDC, click the “Add kerberose realm” button to add the Kerberos realm. This configuration screen is shown in Figure 9.5a.

Figure 9.5a: Adding a Kerberos Realm

_images/realm1a.png

Table 9.5a summarizes the configurable options. Some settings are only available in Advanced Mode. To see these settings, either click the “Advanced Mode” button or configure the system to always display these settings by checking the box “Show advanced fields by default” in System ‣ Advanced.

Table 9.5a: Kerberos Realm Options

Setting Value Description
Realm string mandatory; name of the realm
KDC string only available in “Advanced Mode”; name of the Key Distribution Center
Admin Server string only available in “Advanced Mode”; server where all changes to the database are performed
Password Server string only available in “Advanced Mode”; server where all password changes are performed

9.6. Kerberos Keytabs

Kerberos keytabs are used to do Active Directory or LDAP joins without a password. This means that the password for the Active Directory or LDAP administrator account does not need to be saved into the FreeNAS® configuration database, which is a security risk in some environments.

When using a keytab, it is recommended to create and use a less privileged account for performing the required queries as the password for that account will be stored in the FreeNAS® configuration database. To create the keytab on a Windows system, use these commands:

ktpass.exe -out hostname.keytab host/ hostname@DOMAINNAME -ptype KRB5_NT_PRINCIPAL -mapuser DOMAIN\username -pass userpass

setspn -A host/ hostname@DOMAINNAME DOMAIN\username

where:

  • hostname is the fully qualified hostname of the domain controller
  • DOMAINNAME is the domain name in all caps
  • DOMAIN is the pre-Windows 2000 short name for the domain
  • username is the privileged account name
  • userpass is the password associated with username

This will create a keytab with sufficient privileges to grant tickets.

Once the keytab is generated, use Directory Service ‣ Kerberos Keytabs ‣ Add kerberos keytab to add it to the FreeNAS® system.

Then, to instruct the Active Directory service to use the keytab, select the installed keytab using the drop-down “Kerberos keytab” menu in Directory Service ‣ Active Directory. When using a keytab with Active Directory, make sure that the “username” and “userpass” in the keytab matches the “Domain Account Name” and “Domain Account Password” fields in Directory Service ‣ Active Directory.

To instruct LDAP to use the keytab, select the installed keytab using the drop-down “Kerberos keytab” menu in Directory Service ‣ LDAP.

9.7. Kerberos Settings

To configure additional Kerberos parameters, use Directory Service ‣ Kerberos Settings. As seen in Figure 9.7a, two fields are available:

  • Appdefaults auxiliary parameters: contains settings used by some Kerberos applications. The available settings and their syntax are listed in the [appdefaults] section of krb.conf(5).
  • Libdefaults auxiliary parameters: contains settings used by the Kerberos library. The available settings and their syntax are listed in the [libdefaults] section of krb.conf(5).

Figure 9.7a: Additional Kerberos Settings

_images/kerberos1.png